Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Queens: What to Know First
We provide independent Olympia Chimney chimney liner and rebuild service across Queens, with most jobs completed in a single visit and upfront pricing agreed before any work begins. A typical stainless steel liner replacement runs $2,800-$4,500 depending on flue height and diameter, while partial rebuilds start around $3,200. We’re not here to sell you a full rebuild when a liner swap will do, and we’ll show you the camera footage to prove it either way.
This page is for Queens homeowners with an Olympia Chimney liner or masonry setup that’s showing its age, drafting poorly, or failing inspection. Maybe you’re in a 1960s brick two-family in Forest Hills, a pre-war co-op near Woodhaven Boulevard, or a detached in Bellerose with a terra-cotta flue that’s seen one too many freeze-thaw cycles. Wherever you are in Queens, call (516) 531-6315 for a free estimate.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney stainless steel liners (316Ti and 304 series) can develop pinpoint corrosion at the seam welds when Queens’ coastal humidity meets acidic condensate, especially in oil-to-gas conversions where the flue runs cooler. We see this most in hillside homes in Whitestone and Douglaston where the wind drives moisture down the stack. Our fix: pull a new DuraFlex or Gelco liner sized to the appliance, with proper insulation to keep flue gases above the acid dew point.
- The Olympia Chimney flexible liner kits sold through many distributors use a lighter-gauge corrugation that fatigues at the offsets common in Queens’ offset flues, those sideways jog-backs built to clear floor joists in 1940s construction. After a decade of thermal cycling, the creases crack. We replace with a heavier-gauge flexible liner or, when space allows, a rigid Olympia Chimney-compatible system that eliminates the stress point entirely.
- Olympia Chimney’s aluminum liner offerings were marketed for mid-efficiency gas applications through the early 2000s, and they’re still running in thousands of Queens basements. Aluminum doesn’t tolerate the chlorides in Long Island’s natural gas supply; we’ve pulled liners in Jamaica and St. Albans that looked like perforated foil. We upgrade these to a properly sized 316Ti stainless liner, never another aluminum.
- The Olympia Chimney cast-in-place Thermocrete system fails differently: the refractory shell develops hairline shrinkage cracks as the backing masonry settles, especially in Queens homes with the sandy glacial till that shifts with every wet spring. Water gets behind the cast, freezes, and spalls off chunks. We assess whether a HeatShield cerfractory seal will bridge the cracks or if the liner needs full extraction and replacement.
- Olympia Chimney’s connector pipes and tees in the SL series use a rolled-seam construction that can separate where the tee branch meets the main flue, particularly when installers didn’t support the horizontal run properly. In Corona and Elmhurst, we’ve found SL tees hanging by their own weight, leaking CO into the basement. We replace with a welded DuraFlex or Famco tee, properly supported to code, and test with a combustion analyzer before we leave.
Our Olympia Chimney Chimney Liner & Rebuild Process
- 1
Call and schedule. A live person answers, 24 hours a day. We’ll ask about your appliance type, fuel, and what symptoms you’re seeing. No diagnostic charge for the estimate visit.
- 2
Level-2 camera inspection. Our tech runs a chimney camera from top to bottom, documenting every crack, joint, and creosote deposit. You get the photos and a plain-English verdict: what’s wrong, what can wait, and what can’t.
- 3
Parts decision. If your Olympia Chimney liner is salvageable with an OEM part, we’ll source it. If the OEM spec is inferior to what’s available, we explain the trade-off. We carry DuraFlex, HeatShield, Gelco, and Famco on the truck for same-day resolution when possible.
- 4
The repair. Background-checked, uniformed technicians complete the liner pull or rebuild with no-hassle upfront pricing locked in. For rebuilds, we match existing brick and mortar where we can, or we specify why we can’t.
- 5
Testing and documentation. Every liner job gets a smoke test or draft test; gas appliances get combustion analysis. We leave you with photos, the report, and the 90-Day Done Right Promise in writing.
- 6
Cleanup and follow-up. We haul away old liner material and sweep the work area. Russell Haines reviews every job photo before the invoice goes out.
What Olympia Chimney Chimney Liner & Rebuild Costs in Queens
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Olympia Chimney stainless steel liner replacement (single flue) | $2,800 - $4,500 | Flue height, diameter, insulation required, number of offsets |
| Olympia Chimney flexible liner repair or section replacement | $1,200 - $2,400 | Accessibility, extent of damage, whether tee/connector is involved |
| Partial chimney rebuild (above roofline, Olympia Chimney-compatible) | $3,200 - $6,500 | Linear feet of brick, scaffold needs, matching existing masonry |
| Full chimney rebuild with new liner | $8,500 - $14,000 | Height, liner spec, crown and cap requirements, permit complexity |
| HeatShield cerfractory resurfacing (Olympia Chimney cast-in-place) | $1,800 - $3,200 | Flue length, degree of cracking, whether smoke chamber needs treatment |
These are real Queens numbers based on jobs we’ve completed in Bayside, Forest Hills, and along the Woodhaven Boulevard corridor. Every estimate is free, and the price we quote is the price on the invoice. Call (516) 531-6315 for your exact quote.
Why Queens Homeowners Call Hearthstone Chimney Co. for Olympia Chimney Work
We’ve been sweeping and rebuilding chimneys across Queens for over 42 years. In that time, we’ve learned that an Olympia Chimney liner job isn’t about the brand name on the box; it’s about whether the technician knows why that particular liner failed and how to keep the next one from failing the same way.
Our techs carry Olympia Chimney-compatible parts, but they also carry DuraFlex, HeatShield, and Gelco because sometimes the right fix isn’t the OEM spec. The 90-Day Done Right Promise means if it’s not right, we come back, in writing, no arguing. And when you call, a live person answers, 24 hours a day, every day. That’s not a perk. That’s how a company acts when it plans to be in town in thirty more years.
If it’s wrong, we’ll say so. If we fix it, it stays fixed.
FAQs
No. As an independent Olympia Chimney service provider, we are not affiliated with or authorized by Olympia Chimney, but warranty coverage on materials is between you and the manufacturer. Our workmanship is covered by our own 90-Day Done Right Promise. If you have a current Olympia Chimney parts warranty, we’ll help you document the failure for your claim. Call (516) 531-6315 and we’ll walk you through it.
Yes, in most cases. Olympia Chimney’s 304 and 316Ti liners have standardized diameters and connection methods, so quality aftermarket parts from DuraFlex, Gelco, or Famco fit and perform to spec. For proprietary cast-in-place systems, we evaluate whether HeatShield resurfacing or full replacement is the better value. We don’t leave you hunting for obsolete parts. Call for a free assessment.
The camera inspection tells the story. Isolated cracks or minor corrosion spots often justify a targeted repair. Multiple cracks, separation at joints, or corrosion through more than 30% of the surface means replacement. We’ll show you the footage, explain the threshold, and give you both options with real numbers. No work happens until you see what we see.
Most single-flue replacements are completed in one day. Complex offsets, multi-flue systems, or jobs requiring scaffold access in tight Queens lots may run into a second day. We tell you the timeline upfront, not when we’re halfway through. Background-checked, uniformed technicians arrive when we say they will.
A compromised liner lets flue gases, including carbon monoxide, leak into living spaces, and it allows creosote to accumulate in the masonry where it can ignite. In Queens’ older housing stock with balloon framing, that risk travels fast. That said, not every crack is an emergency. Our camera inspection separates what needs immediate attention from what can be scheduled. Call (516) 531-6315 for a free estimate and an honest timeline.
Written by Russell Haines, Owner, Hearthstone Chimney Co. at Hearthstone Chimney Co., serving Queens and nearby areas.